Brake Light Switch for Wilwood master cylinder

This switch screws into the Wilwood Brake Cylinder and provides a signal to the brake light when depressed. Required on models that use a brake light switch on the master cylinder.

	Price:	22.00 ,EA (see below for options and pricing)
	27-16

Wilwood Brake Cylinder Kit

This master cylinder kit provides more braking power with less hand effort. Two finger brake lockup allows all required braking power and still gives you a secure grip on the handlebar. Lightweight too. For all Indy models with hydraulic brakes.

	Price:	99.50 ,EA (see below for options and pricing)
	27-5

Carlisle Ultimax3 drive belt

Heat build-up in drive belts costs horsepower. The double cog design of our Ultimax?3 belt dissipates heat and aids flexibility. Cooler running belts - over 10 degrees cooler than flat-top designs - mean better performance and longer lasting belts. Better flexibility cuts energy loss, allowing more horsepower transfer from the clutch to the secondary. Double cog Ultimax3 belts feature a thicker cross section than flat-top designs. More surface contacts the clutch. That means less slippage over a broad speed range for quicker acceleration. More racers win with Ultimax belts than with any other aftermarket brand. And you can buy exactly this same high technology belt. Go to the front of the pack with Ultimax?3 by Carlisle. Include your Year, Make and Model with your order so we can get the correct belt for you.

	Price:	65.95 , (see below for options and pricing)
	ultimax3

No Slip Drive Sprockets, "Extro's", 2.52 pitch

GENUINE PPD - The greatest anti-ratchet sprocket available. Each sprocket drives off 2 track lugs and the track clip. Extra long center hub length eliminates the possibility of hex shaft slippage. Requires only 2 drive sprockets. For use with track designs that have all windows open. This is the most efficient and durable drive sprocket on the market today. Allows you to run the track looser creating less resistance without causing the track to skip on the drivers. Slide rail modification required on some models. *1" hex fits 2003 and older Polaris and ALL Yamaha. *1-1/16" hex fits Arctic Cat and 2003 Vertical Escape and 2004 and newer Polaris. Sold individually. We recommend the Anti-Stab wheel kit to be installed when using these drivers (they can be found under the rear suspension category)

	Price:	72.95 ,ea (see below for options and pricing)
	No Slip Sprockets
	C/S/O1 Shaft SizeHex -1"Hex -1-1/16" & 1-1/8"Hex -1-1/4" O/P1 Eight Tooth Sprockets - 72.95 Nine Tooth Sprockets - 77.95 Ten Tooth Sprockets - 89.50

Carlisle Ultimax XS Snowmobile belt

Carlisle is pleased to announce the next generation of snowmobile belt ? Ultimax XS. Ultimax XS is designed for high horsepower sleds and delivers strength and dependability never before available. Carlisle innovation provides superior performance and longer belt life unsurpassed by any competitive belt. Today's high horsepower machines outperform yesterday's drive belts. The Ultimax tradition of quality and innovation continues with the new Ultimax XS. It is the belt you?ve been waiting for. Ultimax XS has increased strength and is built with new heat tolerant materials. With a revolutionary new compound, extra strong Aramax cord, and new manufacturing processes, Ultimax XS will run cooler, longer and faster. Extensive lab and field testing have proven that Ultimax XS can withstand the punishment that today?s super-sleds dish out. Include your Year, Make and Model with your order so we can get the correct belt for you.

	Price:	85.50 ,EA (see below for options and pricing)
	ultimaxxs

Carlisle Max2 snowmobile belt

For general service machines - air-cooled under 500cc - choose the Max2. Its notable strength and tensioning suits lower horsepower machines. This belt powers more snowmobiles than any other aftermarket drive belt in the world! Added flexibility of the new double cog design runs cooler and lasts longer. Each belt meets exacting tolerances, using only the best rubber compounds and a tough ARAMAX? cord. Expect longer life on virtually all general service machines. Nothing ruins a good ride like a broken belt. Riders who use snowmobile belts from Carlisle know only the best get there ... and get home to tell about it. Over a million miles of field testing assures Max2 belts provide the "round-trip reliability" needed for a hard day's ride!. Include your Year, Make and Model with your order so we can get the correct belt for you.

	Price:	31.00 , (see below for options and pricing)
	max2

No Slip Drive Sprockets, "Extro's", 3" pitch

GENUINE PPD - The greatest anti-ratchet sprocket available. Each sprocket drives off 2 track lugs and the track clip. Extra long center hub length eliminates the possibility of hex shaft slippage. Requires only 2 drive sprockets. For use with track designs that have all windows open. This is the most efficient and durable drive sprocket on the market today. Allows you to run the track looser creating less resistance without causing the track to skip on the drivers. Slide rail modification required on some models. *1" hex fits 2003 and older Polaris and ALL Yamaha. *1-1/16" hex fits Arctic Cat, Polaris Edge and post '95 Yamaha. *1-1/4" hex fits Ski-Doo pre-ZX and Arctic cat King Cat. Sold individually. We recommend the Anti-Stab wheel kit to be installed when using these drivers (they can be found under the rear suspension category)

	Price:	$$77.95 ,EA (see below for options and pricing)
	no slip sprockets 3"
	C/S/O1 Shaft sizeHex 1"Hex 1-1/16" & 1-1/8"Hex 1-1/4" O/P2 Teeth - Seven tooth - 77.95 Eight tooth - 89.50

Special Drive track Sprockets for Polaris 1-1/2" and 2" Paddle tracks

7-tooth sprockets are smaller in diameter than stock to increase tunnel clearance for tall traction paddles. Sprockets are available with single or double drivers and have 2.52 pitch for Polaris Hex Shaft. Sold per each. 8-tooth sprockets will allow installation of paddle tracks in the stock Indy chassis. Sprockets are available with single or double drivers and have 2.52 pitch for Polaris Hex Shaft. Sold per each.

	Price:	33.85 ,EA (see below for options and pricing)
	drivers
	O/P1 Size - Single 7 tooth - 18.95 single 8 tooth - 22.80 double 7 tooth - 22.80 double 8 tooth - 20.95 Speedo Adapter for 8-tooth drivers - 47.00

No Slip Drive sprockets "Extro's", 2.86" pitch

GENUINE PPD - The greatest anti-ratchet sprocket available. Each sprocket drives off 2 track lugs and the track clip. Extra long center hub length eliminates the possibility of hex shaft slippage. Requires only 2 drive sprockets. For use with track designs that have all windows open. This is the most efficient and durable drive sprocket on the market today. Allows you to run the track looser creating less resistance without causing the track to skip on the drivers. Slide rail modification required on some models. We recommend the Anti-Stab wheel kit to be installed when using these drivers (they can be found under the rear suspension category). *1" hex fits 2003 and older Polaris and ALL Yamaha. *1-1/16" hex fits Arctic Cat, Polaris Edge, post '95 Yamaha. *1-1/8" fits Ski-Doo ZX and Rev.

	Price:	89.50 ,EA (see below for options and pricing)
	2.86pitch
	C/S/O1 SizeEight tooth x 1" hexEight tooth x 1-1/16" hexEight tooth x 1-1/8" hex

Bottom gear for Ski-Doo, (non hyvo)

no image

Precision cut top and bottom gears. Superior strength, Heat treated, Case hardened steel. Each gear cut precisely to ensure proper fit and deliver the maximum efficiency. Due to the fluctuation in steel prices and costs from the suppliers, prices are subject to change without notice, you will be contacted via email or phone if the price is different than advertised.

	Price:	28.90 ,EA (see below for options and pricing)
	ski doo bottom gears
	O/P1 Bottom gear 11W - -33 tooth - 28.90 -34 tooth - 29.90 -35 tooth - 30.50 -36 tooth - 31.25 -37 tooth - 32.25 -38 tooth - 33.00 -39 tooth - 33.90 -40 tooth - 34.90 -41 tooth - 35.61 -42 tooth - 36.50 -43 tooth - 36.60 -44 tooth - 41.40 -45 tooth - 42.00 O/P2 Bottom gear 13W - -33 tooth - 28.90 -34 tooth - 29.90 -35 tooth - 30.50 -36 tooth - 31.25 -37 tooth - 32.25 -38 tooth - 33.00 -39 tooth - 33.90 -40 tooth - 34.90 -41 tooth - 35.61 -42 tooth - 36.50 -43 tooth - 36.60 -44 tooth - 41.40 -45 tooth - 42.00 O/P3 Bottom gear 15W - -33 tooth - 28.90 -34 tooth - 29.90 -35 tooth - 30.50 -36 tooth - 31.25 -37 tooth - 32.25 -38 tooth - 33.00 -39 tooth - 33.90 -40 tooth - 34.90 -41 tooth - 35.61 -42 tooth - 36.50 -43 tooth - 36.60 -44 tooth - 41.40 -45 tooth - 42.00

Top gears for Ski-Doo (non hyvo)

no image

Precision cut top and bottom gears. Superior strength, Heat treated, Case hardened steel. Each gear cut precisely to ensure proper fit and deliver the maximum efficiency. Due to the fluctuation in steel prices and costs from the suppliers, prices are subject to change without notice, you will be contacted via email or phone if the price is different than advertised.

	Price:	14.17 ,EA (see below for options and pricing)
	ski doo gears
	O/P1 Top gears 11W - -16 Tooth - 14.17 -17 tooth - 15.05 -18 tooth - 17.25 -19 tooth - 18.20 -20 tooth - 19.60 -21 tooth - 17.61 -22 tooth - 18.60 -23 tooth - 22.00 -24 tooth - 23.00 -25 tooth - 24.00 -26 tooth - 25.00 O/P2 Top gear 13W - -16 Tooth - 14.17 -17 tooth - 15.05 -18 tooth - 17.25 -19 tooth - 18.20 -20 tooth - 19.60 -21 tooth - 17.61 -22 tooth - 18.60 -23 tooth - 22.00 -24 tooth - 23.00 -25 tooth - 24.00 -26 tooth - 25.00 O/P3 Top gear 15W - - -16 Tooth - 14.17 -17 tooth - 15.05 -18 tooth - 17.25 -19 tooth - 18.20 -20 tooth - 19.60 -21 tooth - 17.61 -22 tooth - 18.60 -23 tooth - 22.00 -24 tooth - 23.00 -25 tooth - 24.00 -26 tooth - 25.00

Top and Bottom Ski-Doo Hyvo gears.

no image

HYVO gears for Ski-Doo. Limited availability on the bigger sprockets at this time. Due to the fluctuation in steel prices and costs from the suppliers, prices are subject to change without notice, you will be contacted via email or phone if the price is different than advertised.

	Price:	14.20 ,EA (see below for options and pricing)
	doo hyvo
	O/P1 Top gear - -16 tooth - 14.20 -17 tooth - 15.20 -18 tooth - 16.20 -19 tooth - 18.20 -20 tooth - 19.00 -21 tooth - 20.00 -22 tooth - 21.00 -23 tooth - 22.00 -24 tooth - 22.95 -25 tooth - 23.90 -26 tooth - 24.90 O/P2 Bottom gear - -33 tooth - 37.70 -34 tooth - 36.40 -35 tooth - 36.40 -36 tooth - 36.40 -37 tooth - 37.70 -38 tooth - 37.70 -39 tooth - 38.90 -40 tooth - 38.95 -41 tooth - 39.95 -42 tooth - 40.20 -43 tooth - 40.40 -44 tooth - 40.60 -45 tooth - 40.60

HRP Chaincase roll kit for Polaris Edge chassis

Improve track angle and track speeds with this new, easy to install rolled chaincase kit. Kit relocates driveshaft down 5/8" for increased tunnel clearance. Includes locating plates, all necessary hardware and installation instructions.

	Price:	245.99 ,KIT (see below for options and pricing)
	edgerollkit
	C/S/O1 ApplicationKit for 02-03 RMK (except Escape)Kit for 03 Escape/04-05 Edge RMK

SLP Track/Hifax Anti-Wear Pads

These new wear pads reduce drag and wear on Hifax. Designed for the new Polaris and Ski-Doo long tracks that are not equipped with windows or wear clips on each cross bar. Without these anit-wear pads you will have higher Hifax temperature, more drag against the track and even depositing rubber on the Hifax. Eventual damage to the track is also possible.

	Price:	0.65 , (see below for options and pricing)
	sp25101
	O/P1 Package - Pad - washer and nut 0.65 - SP25102 -pack of 40

TRACK SPROCKET POLARIS

Outside Sprocket 9 teeth -2.52 Pitch .960 Shaft -aLL Model 94-98 Polaris

	Price:	19.74 ,EA (see below for options and pricing)
	KX410838

SPROCKET POLARIS

Center Drive Sprocket 9 Teeth 2.52 Pitch .960 Hex Shaft.

	Price:	22.44 ,EA (see below for options and pricing)
	KX410832

3/4 SPROCKET CLUTCH 35 CHAIN / 12 TOOTH

	Price:	34.14 ,EA (see below for options and pricing)
	MT1234

BEARING 6202-2RS 15MM ID DOUBLE LIP SEALS

This bearing has a double lipped seal for added protection. It measures .590" or 15mm ID x 1.378" or 35mm OD x .433" or 11mm WIDE.

	Price:	3.17 ,EA (see below for options and pricing)
	62022RS

BEARING 6206-2RS DOUBLE LIP SEALS

This bearing has a double lipped seal for added protection. It measures 1.181" or 30mm ID x 2.441" or 62mm OD x .630" x 16mm wide. OEM #405-4039-00. FOR SKI DOO FRONT AXLE

	Price:	4.91 ,EA (see below for options and pricing)
	62062RS

BEARING 6205-1RS DOUBLE LIP SEALS

PEER BEARING WITH ONE RUBBER SEAL. 25 MM X 52 X 15 MM .984" X 2.047 MM .590" 1 SEAL.

	Price:	4.23 ,EA (see below for options and pricing)
	62051RS

UNIVERSAL TRACK CLIP TOOL

A TOOL THAT INSTALLS TRACK CLIPS WITH LITTLE EFFORT. INCLUDES BLOCKS (2) FOR NARROW AND WIDE CLIPS. IMPACT DRIVER NOT RECOMMENDED. SKI DOO OEM #529.0045.

	Price:	62.36 ,EA (see below for options and pricing)
	575800

UNIVERSAL CLIPS (PR)

	Price:	38.25 ,EA (see below for options and pricing)
	CP1766

TRACK CLIP W/ GUIDE CAMOPLAST

TO VERIFY APPLICATION, PLEASE COMPARE THE MEASURMENTS OF OLD CLIP TO THE MEASUREMENTS OF YOUR TRACK CLIPS. L SHAPED GUIDE. ZINC OEM #500003400 FITS CAMOPLAST TRACKS.

	Price:	1.06 ,EA (see below for options and pricing)
	611-409

BEARING 6204-2RS DOUBLE LIP SEA LS

This bearing has a double lipped seal for added protection. It measures .787" or 20mm ID x 1.850" or 47mm OD x .551" x 14mm wide.

	Price:	4.50 ,EA (see below for options and pricing)
	62042RS

TRACK CLIP W/O GUIDE CAMOPLAST

Fits most Camoplast tracks (OEM# 500003300) * No guide * Zinc * Dimensions: A = 1-13/16" / B = 1" / C = 1/2" * Sold each

	Price:	1.06 ,EA (see below for options and pricing)
	611-408

Results 1 - 25 of 102

Go to Page: 1 2 3 4 5	Search Again	Return to Homepage

You have line items in your shopping cart

VIEW CART

CHECK OUT

Empty your cart